Skip to content

Product verification guideline

FCC information

W-DALI Mesh FCC ID: XRSTIMOMWAN301

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

IMPORTANT NOTE:
In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.

End Product Labelling

This transmitter module is authorized only for use in device where the antenna may be installed such that 20cm may be maintained between the antenna and users. The final end product must be labelled in a visible area with the following: "Contains FCC ID: XRSTIMOMWAN301".

Manual Information to the End User

The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user's manual of the end product which integrates this module. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter (W-DALI Mesh) installed.

Industry Canada statement

IC: 8879A-TIMOMWAN301
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

  • this device may not cause interference, and

  • this device must accept any interference, including interference that may cause undesired operation of the device.
    Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:

  • l'appareil ne doit pas produire de brouillage, et

  • l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
    FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  • This device may not cause harmful interference, and

  • This device must accept any interference received, including interference that may cause undesired operation.

FCC Declaration of Conformity

We LumenRadio AB, Johan Willins Gatan 6, 41648 Gothenburg, Sweden, declare under our sole responsibility that W-DALI Mesh comply with Part 15 of FCC Rules.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device is intended only for OEM integrators under the following conditions:

  • The antenna must be installed such that 20 cm is maintained between the antenna and users
  • The transmitter module may not be co-located with any other transmitter or antenna

Caution Exposure:
This device meets the exemption from the routine evaluation limits in section 2.5 of RSS102 and users canobtain Canadian information on RF exposure and compliance.
Le dispositif répond à l'exemption des limites d'évaluation de routine dans la section 2.5 de RSS102et les utilisateurs peuvent obtenir des renseignements canadiens sur l'exposition aux RF et le respect.
This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
Cet équipement doit être installé et utilisé avec une distance minimale de 20 centimètres entre le radiateur et votre corps.
The final end product must be labeled in a visible area with the following:
The Industry Canada certification label of a module shall be clearly visible at all times when installed in the host device, otherwise the host device must be labelled to display the Industry Canada certification number of the module, preceded by the words "Contains transmitter module", or the word "Contains", or similar wording expressing the same meaning, as follows:
Contains transmitter module: 8879A-TIMOMWAN301
where 8879A-TIMOMWAN301 is the module's certification number.

CE

W-DALI Mesh comply with the Essential Requirements of RED (Radio Equipment Directive) of the European Union (2014/53/EU). W-DALI Mesh meet the ETSI EN 300 328 V2.2.2 conformance standards for radio performance.

Other compliances

For other local compliance regulations (CE, UL, CSA, SRRC, C-Tick, etc.) you are responsible as the product manufacturer to ensure all required compliance testing is completed. LumenRadio are happy to advise on compliance testing – please contact LumenRadio for details.

RoHS / REACH

The W-DALI Mesh module complies with directive 2011/65/EU, 2015/863/EU (RoHS) of the European Parliament and the Council on the restriction of the use of certain hazardous substances in electrical and electronic equipment.
The W-DALI Mesh module modules do not contain the SVHC (Substance of Very High Concern), as defined by Directive EC/1907/2006 Article according to REACH Annex XVII.

Radio validation tool

The purpose of this tool is to evaluate RF performance. It can be used to certify for both the ETSI and FCC standards. The tool is also helpful during hardware development to verify the RF behaviour.
To be able to use the radio validation tool, you need to have access to the serial debug and programming pins of the module see pin assignment in order to upload the radio test FW using J-Link.
The radio validation tool is available for download at the LumenRadio online support page.